Soot, smoke, and standing water handled by one crew

Fire and Flood Restoration MEDINA WA

Fire and Flood Restoration MEDINA WA is the service you call when a kitchen fire meets a burst supply line. We handle fire and water damage restoration in MEDINA, Washington for homeowners, landlords, and commercial property managers across King County. One crew dries the structure, pulls the soot, and clears the smoke odor before mold sets in. Call (833) 929-6186.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Fire Damage Restoration Medina — Fire Damage Restoration you can rely on
Careful work. Honest options.
About this service

What Fire and Flood Restoration MEDINA WA Involves

Fire and Flood Restoration MEDINA WA is the combined remediation of fire damage and the water left behind by firefighting, and it is needed whenever a loss involves both heat and moisture. That means extracting standing water, drying structural cavities, removing charred framing and soot-coated drywall, and treating the air so smoke odor does not settle back into the house. The two problems feed each other: water from a 1.75-inch attack line soaks insulation and lumber that already lost its protective char layer, and mold can begin colonizing wet framing within 24 to 48 hours.

In MEDINA, that combination shows up more often than people expect. A kitchen fire on a cold morning gets knocked down fast, then 300 to 800 gallons of water sit in the subfloor and wall cavities. Homes near Lake Medina and in the older blocks off South Court Street Historic District tend to have tight crawlspaces and original lumber that holds moisture longer than modern engineered material. If you are searching for fire and water damage restoration near me in MEDINA WA at 2 a.m., the priority is the same: stop the water, secure the structure, then deal with the smoke.

  • ✓ Mold Stopped Early
  • ✓ Smoke Odor Gone for Good
  • ✓ One Insurance File
  • ✓ Structure Saved, Not Replaced
What's included

What Fire and Flood Restoration Covers

The standard scope covers water extraction, structural drying, soot and char removal, odor treatment, and the rebuild of affected surfaces. Contents restoration, duct replacement, and full roof replacement are scoped separately when the loss calls for them. You get the breakdown in writing before demolition starts.

✓

Water Extraction and Drying

Truck-mounted extraction, industrial dehumidifiers, and air movers set to a calculated drying plan. Daily moisture meter readings go into a log you can hand to your adjuster. Most rooms reach dry standard in 3 to 5 days.

✓

Soot and Char Removal

Soot sponges on salvageable surfaces, drywall saw and pry bar on the unsalvageable sections, HEPA vacuums for fine ash. Thermal imaging cameras confirm no hidden wet pockets or hot spots remain before the walls close.

✓

Odor and Air Treatment

Air scrubbers with HEPA filters run continuously. Hydroxyl generators handle occupied spaces, ozone generators run in unoccupied rooms on a timed cycle, and thermal fogging solution reaches deep porous material. Duct cleaning stops the HVAC from recontaminating the house.

✓

Structural Drying Verification

We do not call a job dry because the surface feels dry. Moisture meter readings and thermal imaging scans confirm the framing and subfloor are at dry standard before any rebuild material goes back in. The verification is documented in the file.

✓

Rebuild to Code

Drywall, insulation, lumber, plywood, paint primer, and trim go back in to Washington State code. Charred structural framing gets sistered or replaced based on measured char depth. Workmanship is covered under a written warranty.

✓

Insurance Documentation

Room-by-room photo sets, moisture logs, thermal scans, and a written scope. We coordinate with Servpro, ServiceMaster Restore, BELFOR, Paul Davis Restoration, Rainbow Restoration, and PuroClean when a carrier assigns a preferred vendor, and we bill the carrier directly where the policy allows.

How it works

How Our Fire and Flood Process Runs

01

Emergency Board-Up

We arrive, secure the property, and stop any active water. Windows and doors get plywood and roofing shingles get a tarp-over. We shut off the electrical circuits that were exposed to water and tag them. Most emergency calls in MEDINA get a crew on site within 60 to 90 minutes, day or night.

02

Water Extraction and Drying

Truck-mounted extraction pulls standing water, then we set industrial dehumidifiers and air movers in a calculated drying chamber. Moisture meter readings go into a daily log. A typical flooded room reaches dry standard in 3 to 5 days; a soaked crawlspace can take 7.

03

Soot and Char Removal

Drywall saw and pry bar come out for the unsalvageable sections. Soot sponges handle the rest of the walls and ceilings, HEPA vacuums pull the fine ash, and thermal imaging cameras confirm no hidden hot spots or wet pockets remain behind the surface.

04

Odor and Air Treatment

Air scrubbers with HEPA filters run continuously through the job. Hydroxyl generators handle occupied spaces; ozone generators run in unoccupied rooms on a timed cycle. Duct sealing tape and duct cleaning stop smoke-damaged HVAC ducts from recontaminating the house.

05

Rebuild and Final Walk

Drywall, insulation, paint primer, and trim go back in to code. We walk the job with you room by room, hand over the drying log and photo documentation, and leave the workmanship under a written warranty. Final walk usually happens 10 to 21 days after the loss.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Thermal Imaging Camera

Finds hidden wet pockets behind walls and hot spots in charred framing that a moisture meter cannot reach. We scan every affected room before demolition and again before the walls close.

Industrial Dehumidifier and Air Mover

Dri-Eaz and Phoenix Restoration Equipment units set in a calculated drying chamber. Air movers drive evaporation, dehumidifiers pull the moisture out of the air. The combination is what gets a room to dry standard in 3 to 5 days.

Air Scrubber with HEPA Filters

Runs continuously through the job to capture fine ash and smoke particles. Air quality contamination is a real health issue after a fire, and the scrubber is the first line of defense.

Hydroxyl Generator and Ozone Generator

Hydroxyl generators treat occupied spaces safely; ozone generators run in unoccupied rooms on a timed cycle. Together they handle lingering smoke odor that surface cleaning cannot reach.

Negative Air Machine

Creates a pressure differential that keeps soot and mold spores from migrating into unaffected rooms during demolition. Standard setup on any job where a wall comes down.

Moisture Meter and HEPA Vacuum

The moisture meter is the verification tool: no wall closes until the reading is at dry standard. The HEPA vacuum pulls fine ash from surfaces and cavities without spreading it back into the air.

Soot Sponges and Encapsulant Sealer

Soot sponges lift residue from walls and ceilings without smearing it. Encapsulant sealer locks charred framing and primed surfaces so odor cannot off-gas back into the room.

Real results

Before and after.

Kitchen Fire and Subfloor Water, Downtown Medina

Before

A stove fire was knocked down with roughly 500 gallons of water. The subfloor and the wall behind the cabinets were saturated, the ceiling was coated in soot, and the smoke odor had already reached the second floor through the HVAC.

After

Water was extracted the same night and the drying chamber ran for four days. Soot was removed, framing was sealed, and the wall and cabinet run were rebuilt. Moisture readings returned to dry standard, and the second-floor odor cleared after duct cleaning.

Attic Fire and Soaked Insulation, South Court Street

Before

An attic fire left char in the roof deck and soaked the insulation with suppression water. The tarp-over was holding, but the roof deck was reading wet and the attic smelled of smoke. The home was pre-1978, so lead-safe protocol applied to the demolition.

After

Saturated insulation was removed, the roof deck was dried over six days, and the roofing shingles were replaced where the tarp-over was not enough. The attic was treated for odor before the deck closed. Final moisture readings were at dry standard across the deck.

Electrical Fire and Shared HVAC, Medina Industrial Park

Before

An electrical fire in one commercial unit sent smoke through the shared HVAC and water into the unit below. Two units were affected, the panel had taken on water, and the business needed to reopen part of the space as fast as possible.

After

The affected unit was isolated, the panel was signed off by an electrician, and the ducts were cleaned before the system ran again. The rebuild was phased so the front of the space reopened in six days and the full unit was finished in three weeks. Both insurance files were documented room by room.

Problems we solve

Problems Fire and Flood Restoration Near Me in MEDINA WA Solves

Most of the damage we see in MEDINA is not from the flame. It is from the water and the smoke that follow, and both get worse the longer they sit.

Ask a pro →
01

Lingering smoke odor months after the fire

We seal charred framing with an encapsulant sealer, run hydroxyl and ozone generators on a timed cycle, and clean the smoke-damaged HVAC ducts. The odor treatment is part of the standard scope, not an add-on.

↗
02

Mold growth after fire suppression water

We extract standing water the same day and set drying equipment immediately. Moisture meter readings are logged daily, and we do not close a wall until the framing reads at dry standard.

↗
03

Cracked or collapsed drywall after the water

We cut out the failed sections with a drywall saw, dry the cavity behind, and replace the drywall once the framing is verified dry. The rebuild is scheduled after drying, not before.

↗
04

Melted electrical wiring and a wet panel

We shut off and tag the affected circuits on arrival, coordinate the electrical scope with a licensed electrician, and do not re-energize until the panel and wiring are signed off.

↗
Proof you can check

Licensed, Certified, and Documented

✓
IICRC Fire and Smoke Restoration Technician (FSRT)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC Water Damage Restoration Technician (WRT)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC Applied Structural Drying (ASD)Institute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe Certified FirmU.S. Environmental Protection Agency
✓
Washington State Contractor LicenseWashington State Department of Labor & Industries
Good questions

Frequently Asked Questions

(833) 929-6186 →

Most residential fire and flood restoration jobs in MEDINA run $3,500 to $18,000 in 2026, with the wide range driven by how much water reached the structure and how much framing has to be replaced. A contained kitchen fire with limited water typically lands near the low end; a loss that soaks a crawlspace and a full wall assembly pushes toward the top. We give you a written scope before demolition so the number does not move.

Fire Damage Restoration Medina does, and we cover all of MEDINA plus the surrounding King County area. We are licensed in Washington State, hold IICRC FSRT and WRT certifications, and run 24/7 emergency dispatch. Call (833) 929-6186 and a crew lead will confirm a window on the phone rather than putting you in a callback queue.

Yes, in most cases. The structure usually survives both losses; what fails is the finish material and the wet insulation. We dry the framing to standard, remove charred drywall and soot-damaged material, treat the air, and rebuild. Full rebuilds are rare. Most MEDINA homes we handle are back to move-in condition in 10 to 21 days from the loss date.

Typically yes, and the two perils are usually covered under the same homeowner policy when the water came from firefighting rather than a flood zone. We document moisture readings, thermal scans, and photo evidence for both portions of the claim and bill the carrier directly where the policy allows. Your adjuster still sets coverage; our job is to make the file clean enough that approval does not stall.

Ready when you are

Call for Fire and Flood Restoration MEDINA WA

Water is still spreading and soot is still etching the walls. We dispatch 24/7 across MEDINA and King County, with a crew on site in 60 to 90 minutes on most emergency calls. One call covers the water, the soot, and the rebuild.

Get Emergency Help (833) 929-6186 →
Request an appointment

Contact Our MEDINA Fire Damage Restoration Team

Call (833) 929-6186 any hour of the day. Our line is staffed 24/7, and we dispatch same-day across Medina, Downtown Medina, and the surrounding King County townships. If you prefer email, send photos and your address to info@firedamagerestorationmedina.com and we will call you back within the hour.

Request received — our team will be in touch shortly.
Tap to call(833) 929-6186