Lingering smoke odor in every room
We find the source with thermal imaging and air sampling, then remove residue, clean the ducts and run hydroxyl generators and thermal fogging until the odor is neutralized, not masked.
Fire Damage Clean Up MEDINA WA means removing soot, smoke residue and firefighting water before they set into your walls and framing. Our IICRC-certified crews handle homes and businesses across King County, from Downtown Medina to the Lake Medina Area. We board up, extract, scrub the air and get your insurance claim moving the same day you call.

Fire Damage Clean Up MEDINA WA is the physical work of removing soot, char, smoke residue and suppression water from a structure after a fire is out. It is not a wipe-down. We use thermal imaging cameras to find heat pockets inside walls, HEPA vacuums and soot sponges on every surface, and air scrubbers with HEPA filters to pull combustion particles out of the air. Charred drywall, insulation and lumber come out with a drywall saw and pry bar, and we dry the framing with industrial dehumidifiers and air movers before any rebuild starts.
In Medina, most calls come from kitchen fires, electrical fires in older knob-and-tube wiring, and attic fires that smolder for hours before anyone notices. Smoke travels through HVAC ducts and settles into closets and crawlspaces, so the odor lingers long after the flames are gone. If you are searching for fire cleanup near me MEDINA, the clock matters: soot turns acidic within 24 to 72 hours and starts etching finishes, and firefighting water can feed mold growth in as little as 48 hours.
Every fire damage clean up job includes board-up, soot and char removal, water extraction, structural drying, duct cleaning and odor neutralization. Reconstruction and contents pack-out are scoped as add-ons when needed, and we tell you which is which before work starts.
Windows and doors get boarded and roof openings get tarped the day you call. We photograph the secured site for your insurer so weather and theft do not add to the loss.
Crews HEPA-vacuum ceilings and walls, wipe with soot sponges and remove charred drywall, insulation and lumber. Debris gets bagged and hauled so the property is clear for drying and rebuild.
Suppression water gets extracted, then industrial dehumidifiers and air movers dry the framing. We meter daily and stop when the wood reads dry, usually in 3 to 5 days.
Smoke travels through ductwork and recontaminates rooms every time the system runs. We clean and seal ducts with duct sealing tape and HEPA filters so odor does not cycle back into living spaces.
Hydroxyl generators, ozone generators and thermal fogging solution neutralize odor molecules in cavities and soft goods. Charcoal odor absorbers stay in place until the final walkthrough confirms the smell is gone.
You call and we roll a crew, day or night. On arrival we secure the site, board windows and doors, and tarp any roof openings so weather and intruders stay out. Expect an on-site assessment within hours, not days.
We photograph every room, take moisture meter readings and map the smoke path with a thermal imaging camera. That data becomes the scope of work your adjuster reviews, so nothing gets missed and nothing gets padded.
Crews HEPA-vacuum ceilings and walls, then wipe with soot sponges and Fiberlock-approved cleaners. Charred drywall, insulation and lumber come out with a drywall saw and pry bar. We bag and haul debris so your property is clear.
Standing suppression water gets extracted, then industrial dehumidifiers and air movers run until framing reads dry on the moisture meter. This usually takes 3 to 5 days, and we check readings daily so drying stops when the wood is actually dry.
Air scrubbers with HEPA filters run throughout, followed by hydroxyl generators and thermal fogging to neutralize odor in ducts and cavities. We walk the property with you, show you the readings, and hand off a written summary for your records.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Finds heat pockets and hidden char inside wall cavities that the eye cannot see, so we do not leave a hot spot behind.
Captures fine soot and combustion particles instead of pushing them back into the air. Air scrubbers with HEPA filters run throughout the job.
Dries framing, subfloor and insulation after firefighting water. Dri-Eaz and Phoenix Restoration Equipment units run until moisture meter readings confirm dry.
Neutralizes smoke odor molecules in cavities, soft goods and ductwork. Hydroxyl units are safe for occupied spaces; ozone runs in unoccupied areas only.
Reads moisture content in wood and drywall daily so drying stops when the structure is actually dry, not on a fixed calendar.
Lifts soot residue from walls and ceilings without smearing it, and seals porous surfaces so odor and residue stay locked in.
A grease fire spread across the cabinets and ceiling. Soot covered the first floor, the range hood and ductwork were coated, and the smell reached the upstairs bedrooms. Suppression water sat in the subfloor near the sink.
Crews cleaned and degreased cabinets, HEPA-vacuumed ceilings and walls, cleaned the ductwork and ran hydroxyl generators for three days. Moisture readings confirmed the subfloor was dry by day four. The family moved back in on day six.
An electrical fire smoldered in attic insulation for hours. Charred insulation and framing sat under a layer of soot, and smoke had drifted down into two bedrooms. The thermal camera found two heat pockets the first inspection missed.
We removed charred insulation and lumber, dried the framing to 12% moisture content over five days, and fogged the attic and bedrooms. Air scrubbers ran continuously. The attic passed inspection and the bedrooms were reoccupied in eight days.
A fire in one unit affected three apartments. Two units had no flames but heavy smoke residue in closets, ductwork and soft goods. The property manager needed each unit documented separately for the carrier.
We cleaned smoke residue in all three units, sealed the ducts and ran air scrubbers. Each unit got its own photo set and moisture log. All three were cleared for occupancy in nine days, and the carrier approved all three scopes.
The fire is out, but the damage keeps moving. These are the problems Medina homeowners call us about most, and how we stop each one before it gets worse.
Ask a pro →We find the source with thermal imaging and air sampling, then remove residue, clean the ducts and run hydroxyl generators and thermal fogging until the odor is neutralized, not masked.
Our crews HEPA-vacuum and wipe surfaces with soot sponges and apply encapsulant sealer where needed. We start the same day we assess so the damage stops spreading.
We extract standing water immediately, set industrial dehumidifiers and air movers, and meter the framing daily until it reads dry. Drying is documented for your adjuster.
We clean and seal the duct system with HEPA filters and duct sealing tape, then verify air quality before the system goes back into service.
Most Medina fire cleanup jobs run $3,500 to $18,000 for a typical single-family home, with small kitchen fires at the low end and whole-floor losses at the high end. Structural drying, square footage affected, contents cleaning and whether reconstruction is needed all move the number. We provide a written scope before work starts so you know the range up front.
We do. Fire Damage Restoration Medina handles fire cleanup in MEDINA, Washington and across King County, including Downtown Medina, Medina Square and the Lake Medina Area. Our crews are IICRC-certified and available 24/7 for emergency calls. Call (833) 929-6186 and we will schedule an on-site assessment, usually the same day.
Standard fire damage clean up in MEDINA includes board-up and site security, soot and char removal, HEPA vacuuming of ceilings and walls, water extraction and structural drying, HVAC duct cleaning, and odor neutralization with hydroxyl generators and thermal fogging. Contents cleaning and pack-out are included when salvageable items are present. Reconstruction is scoped separately.
Yes, most homeowner policies cover fire cleanup in MEDINA WA as part of the dwelling and personal property coverage, including water damage from firefighting. We document the loss with photos, moisture readings and a line-item scope that matches what adjusters expect, which speeds approval. Call us before you sign anything from a contractor your insurer recommends so the scope protects you.
Soot and smoke damage get worse by the hour. Call Fire Damage Restoration Medina at (833) 929-6186 for a same-day assessment. IICRC-certified, insured and local to King County, we will secure your property and start cleanup the day you call.
Call Now (833) 929-6186 →Call (833) 929-6186 any hour of the day. Our line is staffed 24/7, and we dispatch same-day across Medina, Downtown Medina, and the surrounding King County townships. If you prefer email, send photos and your address to info@firedamagerestorationmedina.com and we will call you back within the hour.